Install
Instructions

Elite Super Selective
Side Sliding Window Insert

All Security Boss Window Insert will fit channels that are at least 1" wide.

Select below the height range that corresponds
with your sliding window opening height (Channel).

Flap Size
Pet Opening

width x height
6" x 6"

Range 1

30"
to
 37 1/4"

Range 2

37 1/4"
to
 44 1/2"

Range 3

44 1/2"
to
 51 3/4"

Range 4

 51 3/4"
to
59"

Range 5

59"
to
 66 1/4"

Range 6

 66 1/4"
to
73 1/2"

Super
Selective

Pricing
starts at
$322.99

Pricing
starts at
$338.99

Pricing
starts at
$355.99

Pricing
starts at
$379.99

Pricing
starts at
$395.99

Pricing
starts at
$410.99

View of Bottom Section / Spec Info

The top spring-loaded adjusting section of the Side Sliding Window Insert appears as an "H" piece when viewed from the side. The overall width of this piece is 11/16" (Will fit into most any sliding glass door track).

The spring-loaded adjustment provides for a 3.25" range for proper fitting into your opening. Most top tracks in sliding glass doors do not have any center rails, however, if you do have this feature then the Insert can straddle any rail at the top 9/16" wide or narrower.

The spring-loaded top is secured with 2 thumbscrew locks, accessible from the interior only, so that someone from the exterior of the house would not be able to compress or remove the unit.

The bottom section of the Security Boss Side Sliding Window Insert has an overall width of 5/16". A semi-circle, "C" channel is centered and runs the length of the bottom. This "C" channel is design to straddle the center rail in the channel on the floor that your sliding glass door follows.

By straddling this center rail, the Side Sliding Window Insert will remain centered to the frame of your sliding door when closed to this unit.

Note: If the center rail in the channel on the floor is wider than 5/16", then this patio Insert will not be able to straddle it and as a result may not fit properly in your opening

Measuring for the Side Sliding Window Insert:

To determine which height range will work with your slider, open the slider and measure from the very bottom inside track to the very top inside track. As you look down on the groove that the slider follows on the floor, you may see a thin rail. You will want to measure down past that rail, from the deepest part of the channel on the bottom to the very top inside channel above.

Will Side Sliding Window Insert doors fit all Sliding Windows?

As you look at the base track your window follows; you most often will see a "rail". If this "rail" is 5/16" or narrower,(as you look down on it), then the SB Standard Side Sliding Window Insert should fit your window. All Security Boss Window Insert will fit channels that are at least 1" wide.

Included Weather stripping:

Every Security Boss Side Sliding Window Insert features a replaceable bulb seal that lines both sides of the insert. This bulb seal provides a superior weather seal between the insert and the wall and sliding door. This weather seal can also be replaced if needed very easily by sliding the weatherstripping into the t-slot groove on your patio pet door.



The weather seal is a 3" wide vinyl weather stripping section that attaches to the back side of your sliding door. When an insert is installed, your sliding door breaks the seal between the slider and fixed panel. This weather stripping will seal out any drafts.

Adjustable Height Range:

The top section of the Security Boss Side Sliding Window Insert floats on two tension rods that compress or expand to obtain the best possible fit in the patio door frame. The top is fit into the upper patio slider track and the bottom rests on the bottom slider track. Once in place, there are two thumb bolts that lock the top section into place to prevent the unit from being removed from the outside.

 

How does my Side Sliding Window Insert Lock?

We strongly suggest bracing the door with a stick or an adjustable brace bar; as this immobilizes your slider and is the most effective way to secure your sliding door. We also offer several locking devices for purchase if your situation requires.

Use of Extensions Ranges:

You can add 2 inch extensions to the top of all insert heights to extend their reach or adjustment range. These extensions snap into the top of your insert and fit tightly. No screws or hardware are required. It is possible to add more than two (2) extensions on the Security Boss Inserts. The snap in lock feature of the extensions allow for a stable firm unit regardless of the number of extensions are added.